Car wouldn't start, even after trying to jump it. Took the battery to AutoZone, and was told needed new one. Bought new battery, installed and still wont start.
Tested voltage and am getting Could you point me in the right direction, or tell me how to test before hand what it might be? Thank you in advance!
NHTSA — Engine Problems
Do you. Hello, I'm Danny.
Yes, if you are hearing a click sound from under the hood with a no start condition it sounds like the starter motor solenoid may be defective. If you take the starter to your local auto parts store they will test for free. Hope this helps and thanks for using 2CarPros. Danny- Was this answer. Welcome to 2CarPros. First, it could be a few things. Since you hear a clicking from the fuse box, It's unlikely that it's a fuse, but lets confirm that.
Under the hood in the fuse box, locate the 40 amp ign2 fuse.
That is the fuse that sends power to the starter relay. See pictures 1 and 2 If the fuse is good, we need to check the starter relay.
It is located under the hood in the power distribution box. See pic 3. If you see a different relay in the box with the same part number, switch them to see if it makes a difference. It isn't hard, but will require a test light or voltmeter to check. On the starter, you will find a large wire that runs direct from the battery positive. It will always have battery voltage. There will be a smaller wire that is on the solenoid S terminal.
The smaller wire only gets power when the key is in the start position. That is what needs checked, so you will need a helper to turn the key while you check.
If you find there is 12v to the S terminal smaller wire and the larger wire is connected to the battery and the starter doesn't engage, the starter is bad. Remember, the battery must be disconnected prior to working on the starter. Removal Pic 4 Starter 1. Disconnect the battery negative cable. Remove the 2 bolts holding the starter, then remove the starter.
Tightening torque : Installation is the reverse of removal.Hyundai Oil Filter. Hyundai Drain Plug Washer. Hyundai Air Filter. Hyundai Catalytic Converter.
Hyundai Brake Light Switch. Hyundai Rod Bearing. Hyundai Valve Stem Seal. Hyundai Water Pump. Hyundai Door Lock Cylinder. Hyundai Car Mirror. Hyundai Sun Visor.
Hyundai Fog Light.
Hyundai Santa Fe (2015 – 2016) – fuse box diagram
Hyundai Bumper. Hyundai Power Window Switch. Hyundai Windshield Washer Nozzle. Hyundai Emblem. Hyundai Brake Pad Set.
Hyundai Grand Santa Fe (2013 – 2016) – fuse box diagram
Hyundai Brake Caliper. Hyundai Brake Disc. Hyundai Coil Springs. Hyundai Coil Spring Insulator. Hyundai Cruise Control Switch. Hyundai Lug Nuts. Hyundai Steering Wheel. Hyundai Wiper Blade. Hyundai Cabin Air Filter. Hyundai Antenna. Hyundai Wiper Arm. Hyundai Light Socket. Hyundai Headlight. Hyundai Relay. Hyundai Door Jamb Switch. Hyundai Torque Converter. Hyundai Shift Cable. Hyundai Brake Proportioning Valve. Hyundai Neutral Safety Switch. Hyundai Axle Shaft. Hyundai Transfer Case Seal. Hyundai Clutch Fork.Avoid a trip to the mechanic by trying to troubleshoot problems yourself in your Hyundai Santa Fe.
Air conditioning problems are quite common, and can often be quite simple to diagnose and even fix. Take a few easy steps to try and determine the cause of the air conditioning problems. See if the problem is as simple as a blown fuse.
If the temperature controls on the dashboard seem to work correctly but have no effect on the air, then this is likely the problem. The fuse box in a Hyundai Santa Fe is located on the side of the dash to the left of the steering wheel. Pry off the fuse panel cover. Replace the blown fuse with one of equal amperage to avoid damaging the electrical system.
Check the control panel if the controls do not work at all. Find the control panel by prying off the top instrument panel around the air conditioning temperature controls. Unscrew four screws, one in each corner, and remove the temperature control panel. Unplug four electrical connectors and one vacuum hose to the control panel. Listen for the blower motor while adjusting the controls. Get to the blower motor in your Hyundai Santa Fe by first disabling the airbags. Unscrew the glove box and remove it.
Unscrew and remove the blower motor wire harness found directly behind the blower motor. Unscrew three screws holding the blower motor into place and then remove the motor.Fuse box location and diagrams: Hyundai Santa Fe (TM; 2019-..)
Check the coolant levels. The coolant reservoir is found under the hood at the very front of the vehicle. It is white and plastic. Open the cap and shine a flashlight into the reservoir. Make sure the coolant level is less than the full line but more than the low line. This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.
To submit your questions or ideas, or to simply learn more about It Still Works, contact us.So how do you find out what problems are occurring?
Any duplicates or errors? It's not us. Don't waste your time wasting ours! If you are interested in advertising a for-profit service, contact us. Find something helpful? Spread the word. Share on Facebook Retweet this page Email this page. Add Complaint. The contact owns a Hyundai Sonata. The contact stated while driving 65 mph, the vehicle stalled with check engine warning light, and the oil level and battery voltage warning lights illuminated.
The contact pulled over and parked on the side of the roadway. The vehicle was not drivable. The vehicle was towed to his friend's residence. A dealer was not contacted. The vehicle had not been diagnosed nor repaired.
The manufacturer had not been informed of failure. The failure mileage wasMy vehicle engine is stalling yet my VIN is not on the list and it should be added to the list because my engine is coughing and I would like the issue resolved before it shuts down on me.
I was on the highway driving and as I begin to accelerate the car felt as if it was about to stall out.The 3rd generation Santa Fe is equipped with the relatively newer style low profile mini blade fuses.
A white plastic fuse puller tool should be included on the engine bay electrical block. The engine bay fuse box is located next to the air filter housing and behind the driver side headlight assembly. Push in the tab on the front edge of the fuse box cover to release the retaining clip. Then push in the tab on the back side of the cover to release the second retaining clip. Turn over the cover to view the fuse location diagram. There is also another fuse location diagram in the owner's manual.
The interior passenger compartment fuse panel is located behind a rectangular shaped access cover on the bottom left of the dashboard. It is located near where the driver's left knee would normally reside. Insert your fingers in to the opening at the bottom of the access cover and gently pull it straight out. Pinch the end of the fuse puller tool to open the jaws. To check the old fuse, hold it up to a light bulb. If the thin metal strip in the translucent plastic middle of the old fuse appears to be burnt or broken, the old fuse is most likely faulty or "blown" and should be replaced with a new one of the same amperage rating.
If the metal band or bar in the center of the old fuse appears to be intact, the old fuse is most likely still good. Since new fuses are so inexpensive, the old fuse should still be replaced as part of your electrical issue troubleshooting process. Line up the engine bay fuse box cover and push it down in to place until you hear or feel the two retaining clips "click". Re-insert the top edge of the interior fuse panel access cover in to the dashboard and then gently pop in the bottom edge.
If you are still having the same issue, there may be a shorted wire or the component itself needs to be replaced. Be sure to record the fuse change in your vehicle's service records.
If you found this guide to be helpful, please consider making a small donation by clicking on the PayPal. Thank you! Note: I am not a registered charity.Quick Links.
See also: Quick Reference Manual. Support - Hotline. International Toll Free Number: 18 23 53 Car Navigation System. Table of Contents. Page 2 Thank you for purchasing this Car Navigation system. You must stop at a safe place to use with the engine stopped. Page 6 Coordinate Page 7 Table of contents Avoid street MAP button - When it is pressed and held 0. Page 11 Name of each component 6. Press the engine start button or set the ignition key to On or ACC.
This function lets you automatically store the - The frequency moves up and down strong broadcast stations. Select the band FM, AM you want. You can play music fi les saved in a USB the desired fi le. This function plays the fi rst 10 seconds of the set of fi les repeatedly. Press [ ] in menu screen. You can play image fi les saved in a USB memory device. The images list. Connect an auxiliary device to the AUX terminal. Press the screen repeatedly during video playback.
Before playing the Bluetooth audio Audio]. Page Operating Navigation Screen Getting started with navigation 8. Remaining distance display Operating Navigation Screen north up 2D : The map will always Displays the remaining distance to the point north, regardless of the direction The navigation system displays various destination.
Press to check the destination that the vehicle is moving. Page Navigation Volume Getting started with navigation Navigation volume General operations of map General operations of menu navigation menu Press [ ] or [ ] to adjust the volume. Press [ ] on the map screen. Otherwise, drive in accordance with destination] menu automatically. Page Tour Searching for destination of navigation 3.
Press [Set as destination]. Press [Add tourpoint] to set tourpoint.If your trailer weight exceed Tail Gate Back Panel. This variable force solenoid valve directly controls the hydraulic pressure inside the overdrive clut Manuals New Top Sitemap Search manuals.
Repair procedures. Removal 1. Disconnect the battery negative cable and wait for at least three minutes before beginning work. Remove the wiring fixing clip C and disconnect the horn connector A. Release the connector locking pin, then disconnect the driver airbag module connector C. The removed airbag module should be stored in a clean, dry place with the pad cover facing up. Disconnect the clock spring and horn connector, then remove the clock spring. If any improper parts are found during the following inspection, replace the airbag module with a new one.
Never attempt to measure the circuit resistance of the airbag module squib even if you are using the specified tester. If the circuit resistance is measured with a tester, accidental airbag deployment will result in serious personal injury. Check hooks and connectors for damage, terminals for deformities, and harness for binds. Install the airbag module to the steering wheel to check for fit or alignment with the wheel.
If, as a result of the following checks, even one abnormal point is discovered, replace the clock spring with a new one.
Hyundai Santa Fe 2016 Owner's Manual
Check connectors and protective tube for damage, and terminals for deformities. Disconnect the battery negative cable from the battery and wait for at least three minutes before beginning work. Connect the clock spring harness connector and horn harness connector to the clock spring. Set the center position by setting the marks between the clock spring and the cover into line. Connect the driver airbag DAB module connector and horn connector, and then install the driver airbag DAB module on the steering wheel.
First, fix the wire on the fixing clip and then connect the connecter.
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.